Search results

Those links are just turn buckles from another car. I got them from AsiaTees. I ordered them before I did my research. I think you are better off ordering the pipe rod (also from AsiaTees). Those pipe rods looks almost identical to the stock links. I used to mount the upper links where the...

I like the led bar!

Here is the link to the shafts https://m.ebay.ca/itm/2PCS-1-10-RC-Crawlers-Steel-Universal-Drive-Shaft-88-115mm-For-AXIAL-SCX10-/182720731492

There are only 3 gears in the transmission and it's pretty obvious where each belong. You should be fine. I am sort of new to this and I had no problem. I am also wondering if your motor shaft is perfectly parallel to the spur gear and if the pinion is perfectly centered on the motor shaft. You...

I haven't had time to take it outside yet but I don't think it will make a huge difference in performance. What it will do though is make the car run smoother. The stock ones with universal joints don't turn very smoothly and the car gets very jerky when moving at higher speed. Replacing the...

I have the same servo as you and this servo horn will fit nicely https://www.amainhobbies.com/team-associated-factory-team-aluminum-servo-horn-25tfutaba-savox-protek-asc1363/p493940 As for your noise, there are two things you can try. Lightly grease the transmission. Check the pinion/spur gear...

Changed a bunch of stuff over the winter/spring. I think I am finally happy with where things are now, at least until I have more spare cash for other mods. Changes so far: - Metal bumper/skid plate - Generic metal geared servo that seems to work pretty well - Axial bead locks - RC4WD mud...

The drive shafts finally arrived today. It doesn't fit the side with the spur gear. It will rub against the gear cover and the transmission housing. It will probably work if I keep the cover off and grind down the shaft a little. The other side should fit just fine but I can't test it since I...

Hopefully the eBay ones will work. It's hard to tell from the photo. I will keep you guys posted once I get it but I have no idea how much longer it will take. The tracking said it left China like 2 weeks ago but it was updated and said it left China again today....

They haven't arrived

For sure but it may take a while to arrive since it's coming from China.

I ordered these last week. I think they will work but don't know for sure. I think they are a little long but I can always cut them if they are. The stock ones don't exactly bind but I found them kind of rough that's why I want to try a CV shaft...

I am using the 370 motor from a barrage

I have 19mm extenders and heavier than stock wheels as well. With the stock electronics, the wheels barely turns when the truck is not in motion. I got a generic brand metal geared servo from Amazon and now it's a 100 times better. Now I am using HW1080 ESC as well but even before that...

Both unless you can find a receiver that can pair up with the stock remote. This is a pretty affordable set https://www.asiatees.com/display?Miscellaneous-All-Parts-Hop-Ups-Upgrades&brand=Miscellaneous&model=All&id=60437&pid=1

I got the 80a one because it comes with a programming card/box. If you don't care about that, the 60a will be good as well. I suggest you do some more research though as I don't really know that much lol. I can only tell you what worked for me

While the hobby wing esc comes with a programming card for you to adjust settings it's not necessarily the settings that give you better control. You just get much more granular throttle control on the better esc. For example, the stock esc gives you 10 steps between no throttle and full...

Do you have any issue with the center drive shaft caused by the steep angle?

I had the latrax 370. You will gain a lot more speed but if you have the stock esc, you won't have much control at low speed. It's way too fast even at the minimum speed. I went from that motor to the 370 from a barrage. The barrage one is slightly better but still not very controllable at low...

Oh, that sucks but thanks for the info.